Hi In this section, I want to focus on 3G - WCDMA deployments. In these days I tested many WCDMA connectivity options using mobile sim cards. I want to share some important things which will be helpful for any engineer for WCDMA installations.
Important things to remember in WCDMA configuration –
In WCDMA we need to configure proper APN name for connectivity.
You can check apn from – show cellular 0 all
I would like to explain you full process of testing -
Check the router and other components received with router for WCDMA testing.I will give example for Maipu 1800-22-AC router. I used that one for testing.You will get external module – RM2 – 3G- GSM. In which you can insert simcard.Then insert that module in 3/0 slot of Router. Power on router , you can see the after booting …
It will show you like below -
Cellular 3/0 is loading,please wait...
%LINEPROTO-5-UPDOWN: Line protocol on Interface cellular3/0, changed state to up
Cellular 3/0 Load OK
%LINK-5-UPDOWN: Interface cellular3/0, changed state to up
Then you can see one cellular interface in router…
Then you can do below configuration to connect internet –
First configure APN name –
You need to configure this command in privilege mode
Router#cellular 3/0 wcdma apnconfig xxxxxx (eg.- airtelgprs)
Then do below configuration -
Router#
Router#conf t
Router(config)# ip access-list standard 1
permit any
exit
Router(config)# dialer-list 1 protocol ip permit
Router(config)# chat-script g3dia ATDT
Router(config)# int celluar 3/0
interface cellular3/0
encapsulation ppp
ppp chap password ^QVW
## you can configure any password like 123,no need to wait for any password from ISP###
ppp ipcp dns request
ip address negotiated
bandwidth 384
dialer in-band
dialer idle-timeout 0
dialer-group 1
dialer string *99#
script dialer g3dia
ui-control inaccessible telnet http
exit
Router(config)# ip route 0.0.0.0 0.0.0.0 cell 3/0
Then for testing, you can ping 4.2.2.2 , it is global dns IP. Easy to remember
As you will get ping response. Check cellular interface it will get some ip address from ISP. Since this is a dialup connection. As you will send request to LAC , it will forward to LNS and LNS will authenticate you using APN name. So apn name is important.
In this testing troubleshooting is very important part – As it is dialup connection, Need to know where exactly is problem. I think many of you remember ISDN installations. Many times we need to do debug to find exact issue.
Here also its same. But in this case it will be easy. Since we all know PPP well. Before doing ping again, you have to do shutdown and no shutdown under cellular interface.
Then under privilege mode
Router# debug ppp negotiation
Router# debug ppp packets cellular
### Make sure that your terminal monitor is enable or you are using console. ###
Then ping again
Router# ping 4.2.2.2
You can see some logs.
Check the process which is the wrong
PPP negotiation process is easy for you.
LCP-- authentication-- IPCP
Be careful about magic number , compare the sent and received magic numbers, It should be same and authentication is right or wrong.Then the very important is at least should be got local IP address with 32 bit network mask.
And most of all ISP for the WCDMA not require the username and password . but why we need configure it ? Because they need the authentication process. So any password is ok like 123. To check the sim card is which type of the 3G technology, only confirm with ISP. Or check the brand on the USB .
For more detailed information about simcard signal strength – you can check
Show cellular 0 all
In that you can check RSSI under radio information. The range of signal is from -11 dbm to -135 dbm.(-11 is best and -135 is worst).
Now I hope you are very clear with this WCDMA process.
I done above configuration, Here are result outputs-
Before Pinging
router#sh ip int brief
Interface IP-Address Status Protocol Description
fastethernet0 unassigned down down
fastethernet1 unassigned down down
vlan1 192.168.1.1 down down
cellular3/0 unassigned up up
null0 unassigned up up
Pinging
router#ping 4.2.2.2
Press key (ctrl + shift + 6) interrupt it.
Sending 5, 76-byte ICMP Echos to 4.2.2.2 , timeout is 2 seconds:
!!!!!
Success rate is 100% (5/5). Round-trip min/avg/max = 283/303/366 ms.
router#
router#sh cellular 3/0 all
Hardware Information
====================
Modem device name = EM770W
Modem manufacturer = huawei
Modem Firmware Version = 531.11.00.14.113
Hardware Version = MD32TCPU
International Mobile Subscriber Identity (IMSI) = 405801170048287
International Mobile Equipment Identity (IMEI) = 357030021728958
Modem Status = online(full functionality)
Profile Information
====================
Profile 1 = ACTIVE
--------
PDP Type = IP, Header Compression = OFF Data Compression = OFF
PDP address = 0.0.0.0
Access Point Name (APN) = xxxxxxgprs
Network Information
====================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = WCDMA(Attached)
Packet Session Status = active
Current Roaming Status = Home
Network Selection Mode = Manual
Location Area Code (LAC) = 196676
Cell ID = 65690823
Registered PLMN = , Abbreviated = , numeric = 405801
Radio Information
====================
Current RSSI = -93dBm
Security Information
===================
Card Holder Verification (PIN) Disabled
SIM Status = OK
SIM Protection = Disabled
SIM User Operation Required = None
Number of Retries remaining = 3
router#
router#ping
Protocol [ip]:
Target IP address or hostname: 4.2.2.2
Repeat count [5]: 500
Datagram size [76]:
Timeout in seconds [2]:
Extended commands [no]:
Sweep range of sizes [no]:
Press key (ctrl + shift + 6) interrupt it.
Sending 500, 76-byte ICMP Echos to 4.2.2.2 , timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!
Success rate is 100% (500/500). Round-trip min/avg/max = 249/286/1883 ms.
After pinging – you can see now we got IP from ISP by ppp negotiation process.
router#sh ip int brief
Interface IP-Address Status Protocol Description
fastethernet0 unassigned down down
fastethernet1 unassigned down down
vlan1 192.168.1.1 down down
cellular3/0 59.137.26.203 up up
null0 unassigned up up
router#
For internet sharing, we can configure NAT and share internet to local users. This I already explained in previous 3G post –
In previous 3G posts I shared CDMA2000 configuration details, But not much focused on WCDMA. This time I tried my best to explain you about WCDMA.
Hope this post will be helpful for you.
For any feedback and queries, Plz comment with your name and Mail Id. You can use Name/URL option for same.
